Jbl ON BEAT

Voici un extrait du manuel du Jbl ON BEAT que vous pouvez télécharger gratuitement :

Owner’s Manual speaker dock for iPod/iPhone/iPad Jbl ON BEAT OnBeat™ 2 Important Safety Instructions Please read thefollowing precautions before use: Regulations FCC Statement and Warning.

Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat.

Do not defeat the safety purpose of the polarized or grounding-type plug.

A polarized plug has two blades with one wider than the other.

A grounding-type plug has two blades and a third grounding prong.

The wide blade or the third prong is provided for your safety.

If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles and the point where they exit from the apparatus.

Only use attachments/accessories specified by the manufacturer.

Use only with the cart, stand, tripod, bracket or table specified by the manufacturer or sold with the apparatus.

When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

Unplug this apparatus during lightning storms or when unused for long periods of time.

Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15.

Do not expose this apparatus to dripping or splashing and ensure that no objects filled with liquids, such as vases, are placed on the apparatus.

To completely disconnect this apparatus from the AC Mains, disconnect the power supply cord plug from the AC receptacle.

The mains plug of the power supply cord shall remain readily operable.

Do not expose batteries to excessive heat such as sunshine, fire or the like.

This equipment has been tested and found to comply with the limits for aClass B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiateradio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

IC Statement and Warning This Class B digital apparatus complies with Canadian ICES-003.

CAUTION 3www.Jbl ON BEAT.com English connecting and setting up your Jbl ON BEAT OnBeat™ SPEAKER DOCK 1.

Carefully unpack your speaker dock, and confirm that all the items shown here are included: Jbl ON BEAT® OnBeat speaker dock, power supply, AC cord*, remote control, iPod® /iPhone® adapter clip and iPad™ adapter clip.

Connect a USB Type Mini B cable (not included) to the Jbl ON BEAT OnBeat speaker dock USB port and to a USB port on the computer on which your iTunes library is located.

This allows you to sync a docked iPod/ iPhone/iPad device with iTunes® (see Synchronizing with your iTunes Library, on page 6).

If you are going to use your Jbl ON BEAT OnBeat speaker dock with another audio source, plug one end of a 3.5mm (1/8") stereo cable (not included) into the Jbl ON BEAT OnBeat speaker dock Audio In connector, and plug the other end into the audio source’s audio out or headphone USB VIDEO OUTAUDIO INDC IN POWER 3.5mm (1/8") cable IMPORTANT: If you play audio through a docked iPod, iPhone or iPad device and an audio source connected to the Audio In connector at the same time, you will hear both of their outputs mixed through the Jbl ON BEAT OnBeat speaker dock.

To hear only one source, you will need to turn off the other source (the one you do not want to hear) manually.

Important Note for All Electronic Products: Before inserting or unplugging audio cables from the device’s Audio In jack, it is good practice to turn off the device first.

This will prolong the life of your unit, help protect it from static electricity and prevent 4.

If you want to view videos or photos from your iPod, iPhone or iPad device on a TV, plug one end of a composite video cable (not included) into the Jbl ON BEAT OnBeat speaker dock Video Out connector, and plug the other end into your TV’s composite video input connector.

4 When you dock your iPod, iPhone or iPad device on the Jbl ON BEAT OnBeat speaker dock, its video output will automatically be set to Off, even if it was turned On before you docked the device.

To turn the JBL OnBeat speaker dock video output on, press the remote’s Menu button for at least two seconds.

The video from the iPod, iPhone or iPad device will play on the connected TV.

To turn the video output off, press the remote’s Menu button again for at least two seconds.

Insert the included AC cord all the way into the power supply (if there is more than one AC cord, use the correct one for your region).

Then connect the power supply into the JBL OnBeat speaker dock DC In connector and plug it into an AC wall outlet.

Your JBL OnBeat speaker dock includes two adapter clips: one for an iPod touch® /iPod classic® /iPhone device, and another for an iPad device (NOTE: the iPod 5G and iPod nano® models do not require an adapter clip.) The adapters allow you to dock units with or without third-party skins attached.

Attach the appropriate adapter clip to the JBL OnBeat speaker dockdock as shown below.

Bend Clip Slightly Bend Clip Slightly Locking Hole Insert Pin Into Locking Hole iPod touch/iPhone iPad 7.

Make sure the device is inserted all the way onto the connector.

Press the top of the iPod/iPhone/iPad device all the way back into the adapter clip or against the dock to secure it in the dock.

5www.jbl.com English Adjust the volume using the (+) and (–) buttons.

Press both buttons simultaneously to mute the sound; press either button to unmute the sound.

Using your jbl OnBeat SPEAKER DOCK * iPod touch, iPhone and iPad menu navigation may require you to put the iPod/iPhone/iPad device in music mode manually.

Volume UpVolume Down Menu Scroll Down Menu Select/Enter Mute/Unmute Menu Scroll Up Menu Play/Pause* Previous/Rewind (Hold for rewind) Next/Fast Forward (Hold for fast forward) remote control functionsTo turn the JBL OnBeat speaker dock on, press the Power button on the unit.

To turn the JBL OnBeat speaker dock off, press the Power button on the unit again.

To place the JBL OnBeat speaker dock into the Standby mode while an iPod, iPhone or iPad device is docked, hold down the Play/Pause button on the remote for two seconds.

The status LED will glow amber when the unit is in the Standby mode.

To turn the JBL OnBeat speaker dock from Standby to on, press any button on the unit or remote control.

The JBL OnBeat speaker dock will automatically enter the Standby mode whenever no control buttons have been pressed and no audio signal has been present for 10 minutes.

Power Button Volume Buttons 6 rotating the dock When an iPod or iPhone device is docked in the JBL OnBeat speaker dock, you can rotate the dock to the landscape mode.

IMPORTANT: You cannot rotate the dock when an iPad device is docked.

To rotate the dock to the landscape mode, turn it 90 degrees counterclockwise.

To rotate it back to the portrait mode, turn it 90 degrees clockwise.

The dock will hold in place at the portrait and the landscape positions.

Portrait Mode Landscape Mode Synchronizing with YOUR iTunes LIBRARY NOTE: Before attempting to synchronize your iPod/iPhone/iPad device with your iTunes library, be sure that both your iPod/iPhone/iPad device and your iTunes library are updated to the latest software version.

Before attempting to synchronize, be sure that the JBL OnBeat speaker dock USB port is connected to the computer on which your iTunes library is located.

Place your iPod/iPhone/iPad device on the JBL OnBeat speaker dock docking connector.

Make sure the iPod/iPhone/iPad device is inserted all the way onto the connector.

Use your computer’s iTunes software to synchronize the iPod/ iPhone/iPad device with the iTunes library.

When you’re finished synchronizing, eject the iPod/iPhone/iPad device from the iTunes library.

Charging a docked iPod/iPhone/iPad DEVICE The JBL OnBeat speaker dock will charge your iPod or iPhone device whenever it is docked.

NOTE: The JBL OnBeat speaker dock may not charge a docked iPad device via the USB connection to a PC.

If the iPad device charges when it is connected directly to the PC via USB, it will charge while docked on the JBL OnBeat speaker dock.

If the iPad device does not charge when it is connected directly to the PC via USB, it will not charge while docked on the JBL OnBeat speaker dock.

Your JBL OnBeat speaker dock LED will display different colors to indicate the unit’s status: Status LED Status LED Color State White – Constant JBL OnBeat speaker dock is on White – Flashing JBL OnBeat speaker dock is muted Amber – Constant JBL OnBeat speaker dock is in Standby mode No LED JBL OnBeat speaker dock is off 7www.jbl.com English Problem Solution No sound (amber LED is not illuminated): • Make sure that the power supply is properly connected to the JBL OnBeat speaker dock and to a working AC outlet.

No sound (white LED is illuminated): • Touch the Volume Up (+) button to increase the system volume.

• If you’re using a docked iPod/iPhone/iPad device, make sure that it is properly docked in the JBL OnBeat speaker dock.

• If you’re using an auxiliary source, make sure that the audio cable is properly connected to the JBL OnBeat speaker dock Audio In connector and to the source component’s audio output.

• Make sure that the iPod/iPhone/iPad device or other source component is not in the Pause mode and that its volume control is not turned all the way down.